Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!

TUCoPS :: Phreaking Technical System Info :: 2w4w.htm

Basics of Telephony sion Two Wire and Four Wire Transmis
2-Wire and 4-Wire Transmission

Two and Four Wire Transmission

The following sections discuss the 2-Wire line, and typical 2-Wireimplementations within the PSTN. Also discussed is the 'Hybrid', a deviceused to provide 2-Wire to 4-Wire conversions.

2-Wire Line Implementation Within The PSTN

2-Wire loss (End User POT - EO) can be anywhere from 0 dB to 8.5 dB. Usually,the engineered 2-Wire loss will be in the objective range of 4 to 6 dB. Asper a 1980 survey, 4% of subscriber loops had losses greater than 8.5 dB, and2% of subscriber loops exceeded 10 dB.

While the impedance of the telephone is 600 ohms, the impedance of the lineis complex, and will rarely match it, due to the cable characteristics,repeater use, etc.

Usually the total IMPEDANCE of a typical EO POTS line EXCEEDS 900 OHMS (1 Kohmand above). Therefore, many Central Office HYBRID ALIGNMENTS ARE PERFORMEDUSING 900 OHM TERMINATIONS with capacitance.


The Physical Loop Connection

The physical loop connections from the End User Point Of Termination areprovided by the Local Exchange Carriers (LECs) and thusly, regulated by theState's Public Service Commission (PSC) or Public Utilities Commission (PUC).

Cable Connectivity

Most commonly, cables are routed over poles. These telephone pole structuresvary depending upon the load, weather factors, and terrain factors.

Typical practice for rural or suburban areas is to utilize buried cables.The depth of these cables is usually betwen 2 and 4 feet, depending uponlocation, regulatory requirements, future requirements, etc. These cableshave a special waterproof filling with splicing taking place in the ground, orin above-ground pedestals.

In more congested areas, cables are run in conduit, with manholes used forsplicing. Conduit uses a specific heirarchy:

- Main conduits provide interconnective and protection for "feeder" sections of the plant.
- Subsidiary conduits link the "feeder" route to a particular customer location or distribution facility.
- Branch conduit links the underground feeder route to aerial (pole) or buried cable to a single, or group of, building(s).

The length of the conduit is dependent upon many variables, such as locationof intersecting conduit/cables, repeater requirements, physical routingrequirements, and pulling tension. Typically, plastic conduit has a lowercoefficient of friction than concrete or fiberglass conduit, therefore it cansupport longer cable pulls ('runs').

The advantage of conduit is the ability to rerun cables (e.g. replace copperwiring with fiber optic cables, etc.).

Submarine cable is used where land routing is not pratical or possible.Protective materials are placed around the cable, especially in shallow water.Clamps anchor the cable from the action of currents.

Digital Loop Carrier (DLC)

Digital Loop Carrier (DLC) systems were introduced in the 1970s as anefficient way to provide service to a customer, since many more users can besupported over the same amount of wire pairs.

DLC systems are T-carrier based, mutiplexing 24 64 KBPS DS0 channels into T1lines. The basic architecture consists of a Central Office Terminal (COT), aT1 transmission facility (e.g. cable), and a Remote Terminal (RT). Thesesystems also facilitate Central Office diagnostics and offer redundancy andautomatic switching functions upon failures.

Listed below are some of the presently used DLC systems:

The "Hybrid" Transformer

It is not possible to extend, through a telecommunications network, a 2-wiretelephone circuit. Therefore, special 2-Wire to 4-Wire converters, known as'hybrids' provide the conversion to the 4-Wire facilities required.

A basic hybrid contains two transformers and four specific windings: 2-Wireline, 4-Wire Transmit, 4-Wire Receive, and a Balance (or, 'Compromise')Network.

Generally, signals input to the hybrid on the 4W Receive leg of the circuitcan be fed back to the 4W Transmit. THESE SIGNALS RETURN AS 'ECHO'. Thebalance network however, can provide some adjustments such that the signalsfrom the two transformer sections cancel each other out, negating the echo.

THE IMPEDANCE OF THE 2-WIRE LINE DEPENDS UPON THE LENGTH AND WIRE TYPE.Additionally, the only time a 2-Wire circuit has a hybrid switched into it iswhen a call is placed over it to a remote area phone (e.g. most localconnections are 2-Wire). The switching of hybrids also means that different2-Wire lines and Hybrids will be matched up for each call, making precisebalance difficult, since each hybrid and 2-Wire line will have differentcharacteristics.

It is for this reason that the balancing network is sometimes referred to as aCompromise Balance Network; that a happy medium of adjustment is achieved formost circuit connections. ATT Pub 43101 specifies Echo Return Loss (ERL) andSinging Point (SP) values that are listed in the following table:

TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2015 AOH