Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!


TUCoPS :: Phreaking Cellular - Other Manufacturers :: pana04.txt

Panasonic EB 3510/HP600 Programming




PANASONIC EB 3510/HP600

NOTES:  This is a dual NAM hand held unit.
        The ESN prefix is 136 decimal & 88 hex.
        Panasonic: 201-392-6053


NAM PROGRAMING:

1.  This unit requires a programing adaptor, part number EB-WWG1036A, if you
    do not have one try the following:

Locate the expansion connector on the bottom of the phone, remove the plastic
cover if installed.  Look at the connector with the small round antenna
connector to the right (keypad facing up).  There are four pins on each side
(top and bottom) of the connector, the left bottom pin and right bottom pin
must be shorted together.  Use a bent paper clip to do this, the phone will
wake up as soon as the clip makes contact.  The clip must be kept in place
during programing.  Looking at the bottom of the phone:
                   ______________________
                  |                      |
                  |     I  I  I  I       |  <----- Top row.
                  |                   0  |  <----- Antenna connector.
                  |   I  I  I  I         |  <----- Bottom row.
                  |______________________|
                      ^        ^
                      |        |
                      |        |
                    Short these two pins


2.  Phone will automatically power up.

3.  Enter * 0 0 0 0 #, phone will display "MAINT MODE", you are now in
    maintenance mode.

4.  Enter * 1 SND for NAM 1, or * 2 SND for NAM 2.  Phone will display "NAM 1
    MODE" or "NAM 2 MODE".  Note that NAM 2 has entries 01 through 06 only.

5.  Each data entry can be looked at by pressing RCL followed by the
    location (step) number below.

6.  To store new data enter the value, press STO followed by the location
    (step) number below.  For example to enter a system ID of 00031 enter
    00031 STO 01.  Data can be entered or reviewed in any order.

7.  At any time press STO * * to complete programing and return to
    maintenance mode.

8.  At any time press STO # # to ABORT programing and return to maintenance
    mode.

9.  Press * 4 SND to exit maintenance mode.


PROGRAMING DATA:

STEP#    #OF DIGITS/RANGE    DISPLAY        DESCRIPTION

01       00000 - 32767       SIDH           SYSTEM ID
02       10 DIGITS           OWNDL          MIN (AREA CODE & TEL NUMBER)
03       0 OR 1              PRESYS         PREFERRED SYSTEM
04       333 OR 334          IPCH           INITIAL PAGING CHANNEL
05       2 DIGITS            ACCOLC         ACCESS OVERLOAD CLASS
06       2 DIGITS            GIM            GROUP ID (10 IN USA)
07       2 DIGITS            DLMT           DIALED DIGIT LIMIT (00= NO LIMIT)
08       08 ONLY             SCM            STATION CLASS MARK
09       UP TO 12 DIGITS     SPDL           SPEED DIAL NUMBER (PERMANENT
                                            NUMBER STORED IN LOCATION 00)
10       2 TO 4 DIGITS       LOCK           LOCK CODE
11       8 DIGIT, 0 OR 1     FCN 1          SEE NOTE 1 BELOW.
12       8 DIGIT, 0 OR 1     FCN 2          SEE NOTE 2 BELOW
13       8 DIGIT, 0 OR 1     FCN 3          SEE NOTE 3 BELOW


NOTES:

1.  Suggested entry is: 11000000.

Bit 7/Digit 1 = Local use Mark
Bit 6/Digit 2 = MIN Mark
bit 5/Digit 3 = Not Used
Bit 4/Digit 4 = Not Used
Bit 3/Digit 5 = Silent Alert
Bit 2/Digit 6 = Not Used
Bit 1/Digit 7 = Not Used
Bit 0/Digit 8 = Not Used

2.  Suggested entry is: 00010100.

Bit 7/Digit 1 = Not Used
Bit 6/Digit 2 = Built in Monitor
Bit 5/Digit 3 = Auto Lock (if set to 1 and unlock code is unknown phone will
                          NOT enter program mode.)
Bit 4/Digit 4 = Full Lock
Bit 3/Digit 5 = Not Used

(Enable only one of the following)

Bit 2/Digit 6 = Allow user A/B select
Bit 1/Digit 7 = Preferred system only
Bit 0/Digit 8 = Home system only (no Roam)

3.  Suggested entry is: 11000111.

Digit 1 = Received call indicator
Digit 2 = Continuous DTMF
Digit 3 = Send Lock
Digit 4 = Dial Lock
Digit 5 = Not Used
Digit 6 = Enable permanent timer (FCN 1)
Digit 7 = Enable resetable timer (FCN 2)
Digit 8 = Enable individual call timer


READING ESN FROM HANDSET:

1.  Power up phone as above.

2.  Enter * 0 0 0 0 #.

3.  Press * 3 SND.

4.  Press 1 1 SND, phone will display decimal ESN, note that the leading
    "1" of the 136 ESN prefix will be omitted as the phone only has a ten
    digit display capacity.

LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock

UNLOCK: Enter two to four digit code.


A/B SYSTEM SELECT:

1.  Phone will default to preferred/non-preferred on every power up.

2.  A only: F 7 2

3.  B only: F 7 3

4.  Home only: F 7 4 


TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2014 AOH