Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!


TUCoPS :: Phreaking Cellular - Other Manufacturers :: oki-90~2.txt

OKI 900 Debug Mode





==============================================================================
                            OKI 900 - DEBUG MODE
==============================================================================


Here's some info on using the debug mode from the keypad.

Power the phone up.  Wait for PowerOn msg.  Hit 7 and 9 together.
Then hit Menu, Snd, End, Rcl, Sto, Clr.  Phone says good timing!
Debugger is now enabled, but phone works normally.  Hit 1 and 3
together to halt phone and enter debugger.  Everything on display
lights up.  Hit Clr, Clr till you get status display.

Now you can execute commands listed below.  For example to reboot phone
enter #, 0, 2, Snd.  Commands all start with # and end with Snd.  Some
take arguments.

You can use #25, to display memory in EEPROM, and I think once in
that command you can hit # and * to go up and down in memory, Clr to
exit.  Hex chars are entered as "*n", like *1=A, *2=B, etc.


SUSPEND     #01         Performs Initialization
RESTART     #02         Terminates the test mode
STATUS      #03         Shows current status of TRU
RESET       #04         Resets the autonomous timer
TURNAROUND  #05    ?    Returns Data Bytes following command to the Test Set.
INIT        #06         Initialize the TRU to following states:
                         Carrier Off, Attenuation - 0db, Receive Audio Muted
                         Transmit Audio Muted, Signalling tone off,
                         Autonomous timer reset, SAT off, and DTMF off
CARRIER ON  #07         Turns the carrier on
CARRIER OFF #08         Turns the carrier off
LOAD SYNTH  #09XXXX     Sets the synthesizer to channel XXXX
SET ATTN    #10X        Set the RF power attenuation to X
                         0=0db, 7=-28 db (in steps of -4db thru 7)
RXMUTE      #11         Mutes the receive audio
RXUNMUTE    #12         Unmutes the receive audio
TXMUTE      #13         Mutes the transmit audio
TXUNMUTE    #14         Unmutes the transmit audio
RESETOFF    #15         Discontinues resetting of autonomous timer
STON        #16         Transmits a continuous signalling tone
STOFF       #17         Stops transmission of signalling tone
SETUP       #18         Transmits a 5 word RCC message (fixed text pattern)
VOICE       #19         Transmits a 2 word (RCC) RVC message (fixed test pattern)
RCVSU       #20         Receives a 2 word FCC message (cancel with 0x38)
RCVVC       #21         Receives a 1 word (FCC) FVC message (cancel with 0x38)
SEND-NAM    #22         Returns the information contained in the NAM
VERSION     #23
SEND-SN     #24
MEM         #25XXXX     Displays the resident memory data at XX
                          00XX=in micro, XXXX=EEPROM
WSTS        #28         Count 1 word messages on CC, until TERMINATE
WSTV        #29         Count 1 word messages on VC, until TERMINATE
SATON       #32X        Enable the transmission of SAT X
                         0= 5970 Hz, 1=6000 Hz, 2=6030 Hz
SATOFF      #33         Disables the transmission of SAT
CDATA       #34<60>     Transmits 5 word RCC message (30 bytes)
HITNON      #35         Activates the 1150Hz tone to receive audio line
HITNOFF     #36         Deactivates the 1150Hz tone
LOTNON      #37         Activates the 770Hz tone to receive audio line
LOTNOFF     #38         Deactivates the 770Hz tone
DTMFON      #42XX       Enable the transmission of DTMF frequency XX[2]
DTMFOFF     #43         Disable the transmission of DTMF
?           #44
?           #45
?           #46
?           #47
?           #48
?           #51
-           #52<xx>




?           #53
-           #54XXXXZZ   Write HEX (ZZ) into ADDRESS $XXXX
                        if 00XXZZ then store #$YY in MicoRAM $XX
-           #56         Return Value stored in $BEBB
?           #60
?           #62
?           #63
RCVSU       #64         Receives a 2 word FCC message (duplicate of cmd #20)
COMP-ON     #65         Enable the compressor and expandor
COMP-OFF    #66         Disable the compressor and expandor
setvol      #67         X-Set volume (0-7) 0=max
SERIAL I/O  #683XX?     Mutes/Unmute Tx/Rx Audio Signal Enable
                        Disable the Compressor/Expandor, XX=commanded states.
                            CMD Compress Tx Mute Rx Mute
                            --- -------- ------- -------
                            40  on       unmuted unmuted
                            41  off      unmuted unmuted
                            42  on       muted   unmuted
                            43  off      muted   ummuted
                            44  on       unmuted muted
                            45  off      unmuted muted
                            46  on       muted   muted
                            47  off      muted   muted
?           #72          [pulls something, outputs 1 word!?!]
?           #73<arg>

                      Scans channels,...

                       #73 XXXX xxxx YY

                        XXXX = Start channels scan
                        xxxx = End   channels
                         yy  = Time

?           #74
-           #75         Enable Handsfree (disable spkr)
-           #76         Disable Handsfree (enable spkr)
-           #77         Turns on Loudspeaker near mic
-           #79
?           #80
?           #81
?           #84
?           #85



TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2014 AOH