...because we can't all be on the bleeding edge...
DANPEX CORPORATION
AN-500S /AN-500B
|
NIC Type |
ARCnet |
|
Transfer Rate |
2Mbps |
|
Data Bus |
8-bit ISA |
|
Topology |
Star (AN-500S) Linear Bus (AN-500B) |
|
Wiring Type |
Shielded/Unshielded twisted pair RG62A/U 93ohm coaxial |
|
Boot ROM |
Available |
|
NODE ADDRESS | ||||||||
|
Node |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 |
SW2/5 |
SW2/6 |
SW2/7 |
SW2/8 |
|
0 |
- |
- |
- |
- |
- |
- |
- |
- |
|
1 |
On |
On |
On |
On |
On |
On |
On |
Off |
|
2 |
On |
On |
On |
On |
On |
On |
Off |
On |
|
3 |
On |
On |
On |
On |
On |
On |
Off |
Off |
|
252 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
On |
|
253 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
Off |
|
254 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
On |
|
255 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
Note: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 8=1, 7=2, 6=4, 5=8, 4=16, 3=32, 2=64, 1=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, Off=1) | ||||||||
|
RESPONSE AND RECONFIGURATION TIMEOUTS | ||||
|
Response Time |
Idle Time |
Reconfiguration Time |
JP1 |
JP2 |
|
78µs |
86µs |
840ms |
Open |
Open |
|
285µs |
316µs |
1680ms |
Closed |
Open |
|
563µs |
624µs |
1680ms |
Open |
Closed |
|
1130µs |
1237µs |
1680ms |
Closed |
Closed |
|
Note: All NICs on the network must have this option set the same. | ||||
|
INTERRUPT REQUEST | |||||||||||
|
IRQ |
JP3 |
JP4 |
JP5 |
JP6 |
JP7 |
JP8 |
JP9 |
JP10 |
JP11 |
JP12 |
JP13 |
|
2 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
3 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
4 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
6 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
7 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
10 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
11 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
12 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
14 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
15 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
ONBOARD TERMINATOR | ||
|
Setting |
JP14 | |
| » |
Disabled |
Open |
|
Enabled |
Closed | |
|
Note:If the card is the last in the line of network cards, the onboard terminator may be enabled instead of using a T-connector and an external terminator. This setting is valid only with the AN-500B. If using model AN-500S, JP14 must be open. (Star topologies do not require the use of terminators) | ||
|
CARD TYPE | |
|
Card |
JP15 |
|
AN-500S |
Open |
|
AN500B |
Closed |
|
I/O BASE ADDRESS | |||||||
|
Address |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 | |
| » |
2E0h |
Off |
On |
Off |
Off |
Off |
On |
|
2F0h |
Off |
On |
Off |
Off |
On |
Off | |
|
300h |
Off |
Off |
On |
On |
On |
On | |
|
RIM BUFFER ADDRESS | |||||
|
Address |
SW1/7 |
SW1/8 |
SW1/9 |
SW1/10 | |
|
C0000 - C07FFh |
Off |
Off |
On |
On | |
| » |
D0000 - D07FFh |
Off |
Off |
On |
Off |
|
E0000 - E07FFh |
Off |
Off |
Off |
On | |
|
DIAGNOSTIC LED(S) | ||
|
LED |
Status |
Condition |
|
LED1 |
On |
Card is receiving power and is operating properly |
|
LED1 |
Flashing |
Data is being transmitted or received |
|
LED1 |
Off |
Card is not receiving power or is defective |